在Ubuntu Linux下制作Windows 启动安装 USB盘

最近想 ,在上刻录个的安装U盘,在网上看了些资料,不过好多都说的很模糊,于是乎,我走了不少弯路。这里记录下来,希望了帮到大家。

首先你的有个USB吧,这里我们假定USB在ubuntu中为/dev/sdb

1. 给USB设备 /dev/sdb 分区,注意,要是主分区,

sudo fdisk /dev/sdb
Command (m for help): n
Partition type:
  p  primary (0 primary, 0 extended, 4 free)
  e  extended
Select (default p): p
Partition number (1-4, default 1):
Using default value 1
First sector (2048-15564799, default 2048):
Using default value 2048
Last sector, +sectors or +size{K,M,G} (2048-15564799, default 15564799):
Using default value 15564799

Command (m for help): p

Disk /dev/sdb: 7969 MB, 7969177600 bytes
246 heads, 62 sectors/track, 1020 cylinders, total 15564800 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x8d55b9cb

  Device Boot      Start        End      Blocks  Id  System
/dev/sdb1            2048    15564799    7781376  83 

上面/dev/sdb1就分出来了,全部的空间都给了sdb1

2. 然后把/dev/sdb1设置为启动分区

Command (m for help): a
Partition number (1-4): 1

Command (m for help): p

Disk /dev/sdb: 7969 MB, 7969177600 bytes
126 heads, 10 sectors/track, 12353 cylinders, total 15564800 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x8d55b9cb

  Device Boot      Start        End      Blocks  Id  System
/dev/sdb1  *        2048    15564799    7781376  83 

我们可以看到,sdb1后面,多了个*

3. 接下来,把上面做的所有改动写入USB

Command (m for help): w
The partition table has been altered!

Calling ioctl() to re-read partition table.

WARNING: Re-reading the partition table failed with error 22: Invalid argument.
The kernel still uses the old table. The new table will be used at
the next reboot or after you run partprobe(8) or kpartx(8)
Syncing disks.

然后就是q退出

4. 将分区格式化为ntfs的

sudo mkfs -t ntfs /dev/sdb1

这个过程中,会把分区中写入全0,大概会等几分钟

5. 接下来就是把下载好的iso文件dd到这个启动分区了

# 把下载的iso文件刻录到usb的分区中(及得,一定是分区,否则下次用这个usb是会出现 Operating not found的
sudo dd if=/home/peter/Downloads/WindowsTechnicalPreview-x64-ZH-CN.iso of=/dev/sdb1 bs=4M iflag=direct​

看到了吧,我在安装win10

6. 现在还不可以从usb盘启动,还要在usb盘MBR区信息写入,这需要一个工具LILO

sudo apt-get install lilo
sudo lilo -M /dev/sdb mbr

下次启动的时候,选择这个USB启动就会出现的安装界面了!

另外,我自己也试了unetbootin,不过没有成功,选择从U盘启动后,一直卡在一个选择界面。大家有试成功的麻烦推荐下

更多Ubuntu相关信息见

转载自:https://www.linuxidc.com/Linux/2016-01/127511.htm

声明: 除非转自他站(如有侵权,请联系处理)外,本文采用 BY-NC-SA 协议进行授权 | 智乐兔
转载请注明:转自《在Ubuntu Linux下制作Windows 启动安装 USB盘
本文地址:https://www.zhiletu.com/archives-5700.html
关注公众号:智乐兔

赞赏

wechat pay微信赞赏alipay pay支付宝赞赏

上一篇
下一篇

相关文章

在线留言

你必须 登录后 才能留言!

在线客服
在线客服 X

售前: 点击这里给我发消息
售后: 点击这里给我发消息

智乐兔官微